Over 15 years experience of providing support of MEAN WELL Power Supplies
Overview
ODLC-65-700 is the model of this series: rated current 700mA, rated power 65.1W, typical efficiency 88%.
ODLC-65 series is a 65W LED AC/DC driver featuring the constant current mode output with flicker free design. ODLC-65 operates from 180~295VAC and offers models with different rated current ranging between 700mA and 1750mA. Thanks to the efficiency up to 88%, with the fanless design, the entire series is able to operate for -20℃~+85℃ case temperature under free convection. The design of plastic housing and IP67 ingress protection level allows this series to fit indoor wet applications. ODLC-65 is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for lighting system.
Features
- Constant current mode output
- Flicker free design
- Plastic housing with class II design
- Built-in active PFC function
- No load power consumption<0.5W(Blank-Type), Standby power consumption<0.5W(DA-Type)
- IP67 rating for indoor or outdoor installations
- Function options: 2 in 1 dimming (dim-to-off); Auxiliary DC output; DALI
- 3 years warranty
Specifications
OUTPUT
- RATED CURRENT
- 700mA
- RATED POWER
- 65.1W
- CONSTANT CURRENT REGIONNote.2
- 69 ~ 93V
- OPEN CIRCUIT VOLTAGE(max.)
- 118V
- CURRENT RIPPLE
- 5% max. @rated current
- CURRENT TOLERANCE
- ±7.0%
- SETUP TIMENote.4
- 500ms / 230VAC
- AUXILIARY DC OUTPUTNote.5
- Nominal 12V(deviation 11.4~12.6)@50mA for ODLC-65A only
INPUT
- VOLTAGE RANGENote.3
- 180 ~ 295VAC (Please refer to "STATIC CHARACTERISTIC" section)
- FREQUENCY RANGE
- 47 ~ 63Hz
- POWER FACTOR (Typ.)
- PF>0.95/230VAC, PF>0.9/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
- TOTAL HARMONIC DISTORTION
- THD< 20%(@load≧75%/230VAC,277VAC) (Please refer to “TOTAL HARMONIC DISTORTION” section)
- EFFICIENCY (Typ.)
- 88%
- AC CURRENT
- 0.4A/230VAC 0.3A/277VAC
- INRUSH CURRENT (Typ.)
- COLD START 30A(twidth=100μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
- MAX. No. of PSUs on 16A CIRCUIT BREAKER
- 32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC
- LEAKAGE CURRENT
- <0.75mA / 277VAC
- NO LOAD / STANDBY POWER CONSUMPTION
- No load power consumption <0.5W for Blank-Type, <1.2W for ODLC-65A Standby power consumption <0.5W for DA-Type
PROTECTION
- SHORT CIRCUIT
- Hiccup mode,auto-recovery after fault condition is removed for DA type; Hiccup mode,re-power on to recovery for other type
ENVIRONMENT
- WORKING TEMP.
- Tcase=-20 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
- MAX. CASE TEMP.
- Tcase=+85℃
- WORKING HUMIDITY
- 20 ~ 90% RH non-condensing
- STORAGE TEMP., HUMIDITY
- -40 ~ +80℃, 10 ~ 95% RH
- TEMP. COEFFICIENT
- ±0.03%/℃ (0 ~ 45℃)
- VIBRATION
- 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY & EMC
- SAFETY STANDARDS
- UL8750(type”HL”);CSA C22.2 NO.250.13-12; ENEC BS EN/EN61347-1 & BS EN/EN61347-2-13 independent, BS EN/EN62384; EAC TP TC 004, IP67 approved
- DALI STANDARDSNote.7
- Compliance to IEC62386-101,102 for DA-Type only
- WITHSTAND VOLTAGE
- I/P-O/P:3.75KVAC
- ISOLATION RESISTANCE
- I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
- EMC EMISSION
- Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (≧75% load) ; BS EN/EN61000-3-3, GB17743,GB17625.1,EAC TP TC 020
- EMC IMMUNITY
- Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level(surge immunity: Line-Line:1KV),EAC TP TC 020
OTHERS
- MTBF
- 4381.7K hrs min. Telcordia SR-332 (Bellcore) ;402.6K hrs min. MIL-HDBK-217F (25℃)
- DIMENSION
- 121*77*28.5mm(L*W*H)
- PACKING
- 0.43Kg; 24pcs/ 11.3Kg/ 0.74CUFT
Test conditions and notes10
- 1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
- 2. Please refer to "DRIVING METHODS OF LED MODULE".
- 3. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
- 4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time or set up failure
- 5. Aux. 12V will be damaged with short circuit; It will not be available when output voltage is not in constant current region or output no load condition.
- 6. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
- 7. The DALI version driver does not support the bit 1: Lamp failure in the Command 144 Query status of the DALI standard.
- 8. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
- 9. For any application note and IP water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf
- 10. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains.
Technical drawings
Typical applications
- LED panel lighting
- LED flood lighting
- Indoor LED lighting
- Industrial lighting
Downloads
Certificates7
Test reports1
Catalogues1
FAQ
Can I use the ODLC-65-700 for LED downlights with a long series string?
Yes, this model is often a better fit when the LED downlight uses a higher-voltage constant current string, because it delivers 700mA across a 69-93V CC range. The LED load still needs to be designed for constant current operation rather than constant voltage input.
Is the ODLC-65-700 suitable for signage modules or small LED arrays with higher forward voltage?
It can be used for signage modules or small LED arrays that require 700mA constant current and have a combined forward voltage within 69-93V. Its output power is 65.1W, so the connected LED load must stay within that limit.
Can this driver be used in outdoor or harsh environment fixtures?
Yes, the ODLC-65-700 is rated IP67 for indoor or outdoor installations exposed to water and dust. It supports an operating case temperature range of -20°C to +85°C for demanding environmental conditions.
How do I verify LED compatibility with the ODLC-65-700?
The LED assembly must require 700mA constant current, and its total forward voltage must fall within the 69-93V CC output range. The number of LEDs depends on the forward voltage of each LED, so there is no fixed LED count that applies to every load.
How is the ODLC-65-700 different from the other 65W ODLC drivers?
Among the 65W options, the ODLC-65-700 is 700mA with a 69-93V CC range and 65.1W, the ODLC-65-1050 is 1050mA with a 46-62V range and 65.1W, the ODLC-65-1400 is 1400mA with a 34-46V range and 64.4W, and the ODLC-65-1750 is 1750mA with a 27-36V range and 63W. This makes the ODLC-65-700 the highest-voltage, lowest-current version in the 65W group.
Payment & Security
Payment methods
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Other ODLC-65 Models
3 other models| Model | Power | Voltage | Current | IP Rating | |
|---|---|---|---|---|---|
| Mean Well ODLC-65-1750 Power Supply 65W 1750mA, Dimmable | 63W | 36V | 1.75A | IP67 | View |
| Mean Well ODLC-65-1400 Power Supply 65W 1400mA, Dimmable | 64.4W | 46V | 1.4A | IP67 | View |
| Mean Well ODLC-65-1050 Power Supply 65W 1050mA, Dimmable | 65.1W | 62V | 1.05A | IP67 | View |
Please log in to write a review.
Write a review
Reviews are checked before publishing. By submitting you confirm this is your genuine experience with this product.
Submitting your review…
It's published and now helps other buyers.
We're checking it and it'll appear shortly.
Please try again.






