Image shown is a representation only. Exact specifications should be obtained from the product datasheet.

Mean Well HRP-200-15 Power Supply 201W 15V 13.4A

built-in active PFChigh efficiency up to 90%no load power consumption <0.5W~0.75W

SKU HRP-200-15

Log in to see price Trade pricing & online ordering for account holders

Select model — 7 in this family

HRP-200-15

HRP-75-15 75W 15V Backorder

HRP-100-15 100W 15V Backorder

HRP-150-15 150W 15V Backorder

HRP-200-15 200W 15V Backorder

HRP-300-15 300W 15V Backorder

HRP-450-15 450W 15V Backorder

HRP-600-15 600W 15V Low stock

Product variants

Available to order

Overview

HRP-200-15 is the 15V output model of this series: rated current 13.4A, rated power 201W, typical efficiency 88%.

Features

Universal AC input / Full range
Built-in active PFC function, PF>0.95
High efficiency up to 89%
Withstand 300VAC surge input for 5 seconds
Protections: Short circuit / Overload / Over voltage / Over temperature
Cooling by free air convection
Built-in constant current limiting circuit
1U low profile 38mm
Built-in remote sense function
5 years warranty

Specifications

HRP-200-15Specifications from the official datasheet (2026-04-03 edition)

OUTPUT

DC VOLTAGE: 15V
RATED CURRENT: 13.4A
CURRENT RANGE: 0 ~ 13.4A
RATED POWER: 201W
RIPPLE & NOISE (max.)^Note.2: 150mVp-p
VOLTAGE ADJ. RANGE: 13.5 ~ 18V
VOLTAGE TOLERANCE^Note.3: ±1.0%
LINE REGULATION: ±0.3%
LOAD REGULATION: ±0.5%
SETUP, RISE TIME: 1000ms, 50ms/230VAC 2500ms, 50ms/115VAC at full load
HOLD UP TIME (Typ.): 16ms/230VAC 16ms/115VAC at full load

INPUT

VOLTAGE RANGE^Note.5: 85 ~ 264VAC 120 ~ 370VDC
FREQUENCY RANGE: 47 ~ 63Hz
POWER FACTOR (Typ.): PF>0.95/230VAC PF>0.99/115VAC at full load
EFFICIENCY (Typ.): 88%
AC CURRENT (Typ.): 2.1A/115VAC 1.1A/230VAC
INRUSH CURRENT (Typ.): 35A/115VAC 70A/230VAC
LEAKAGE CURRENT: <1.2mA / 240VAC

PROTECTION

OVERLOAD: 105 ~ 135% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed
OVER VOLTAGE: 18.8 ~ 21.8V Protection type : Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE: Shut down o/p voltage, recovers automatically after temperature goes down

ENVIRONMENT

WORKING TEMP.: -40 ~ +70℃ (Refer to "Derating Curve")
WORKING HUMIDITY: 20 ~ 90% RH non-condensing
STORAGE TEMP., HUMIDITY: -40 ~ +85℃, 10 ~ 95% RH
TEMP. COEFFICIENT: ±0.03%/℃ (0 ~ 50℃)
VIBRATION: 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes

SAFETY & EMC (Note 4)

SAFETY STANDARDS: UL62368-1,TUV BS EN/EN62368-1, AS/NZS62368.1, EAC TP TC 004 approved
WITHSTAND VOLTAGE: I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
ISOLATION RESISTANCE: I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION: Compliance to BS EN/EN55032 (CISPR32) Class B, BS EN/EN61000-3-2,-3, EAC TP TC 020
EMC IMMUNITY: Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11,BS EN/EN55035,heavy industry level, EAC TP TC 020

OTHERS

MTBF: 1830.6K hrs min. Telcordia SR-332 (Bellcore) ; 209.5K hrs min. MIL-HDBK-217F (25℃)
DIMENSION: 199*98*38mm (L*W*H)
PACKING: 0.77Kg; 18pcs/14.9Kg/0.87CUFT

Test conditions and notes6

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1μF & 47μF parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on a 360mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf )
5. Derating may be needed under low input voltages. Please check the derating curve for more details.
6. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).

Technical drawings

HRP-200-15 Mechanical Specification — Mechanical Specification

HRP-200-15 Block Diagram — Block Diagram

HRP-200-15 Derating Curve — Derating Curve

Downloads

Certificates4

EMC Certificate (HRP-200)(EN) PDF Download

UL Certificate(HRP-200)(EN) PDF Download

CB Certificate (HRP-200)(EN) PDF Download

TUV Certificate(HRP-200)(EN) PDF Download

Test reports1

Test Report(HRP-200-15)(EN) PDF Download

Catalogues1

Mean Well Catalog (Industrial) PDF Download

FAQ

Can I use the HRP-200-15 for 15V industrial instrumentation?

Yes, if the instrumentation requires a constant 15V source and the total load stays within 201W and 13.4A. That makes it relevant for industrial electronics built around a 15V DC rail rather than the more common 12V or 24V rails. The 85-264VAC input also supports broad AC input conditions.

Is the HRP-200-15 a good fit for test benches or embedded lab equipment that runs on 15V?

It can be a fit for embedded test rigs or bench equipment designed for 15V DC input up to 13.4A. Because it is a constant-voltage unit, the load should be specified for 15V operation. The typical efficiency of 88% can help control heat in enclosed equipment.

Can this power supply support 15V automation or analog control electronics?

Yes, for 15V automation, analog, or measurement electronics that need a fixed 15V output and draw no more than 201W total. Its rated output current is 13.4A, and the output can be adjusted within 13.5-18V if needed. Buyers should still size it against the real steady-state and peak load of the equipment.

What are the other HRP-200 voltage options besides the HRP-200-15?

The HRP-200 family includes 3.3V 132W 40A, 5V 175W 35A, 7.5V 200.3W 26.7A, 12V 200.4W 16.7A, 24V 201.6W 8.4A, 36V 205.2W 5.7A, and 48V 206.4W 4.3A, along with this 15V 201W 13.4A model. Those versions differ mainly by output voltage and current. The right choice depends on the DC rail your equipment is designed to use.

Is the HRP-200-15 suitable for outdoor cabinets or harsh environments?

The operating temperature range is -40°C to +70°C, so the electrical design supports a wide thermal range. However, the provided specs do not list an IP rating, so exposed outdoor use should not be assumed from temperature range alone. For harsher environments, the surrounding enclosure protection still matters.

Payment & Security

Payment methods

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Model	Power	Voltage	Current
Mean Well HRP-200-48 Power Supply 206.4W 48V 4.3A	206.4W	48V	4.3A	View

Please log in to write a review.

{ "id":8343877157163, "variants" :[{ "context":"default", "variant_id": 45320927510827, "sku":"HRP-200-15", "inventory_qty" : 0, "customer" :false, "custom_html" :"\u003ca class=\"text-current logged-out-price logged-out\" href=\"https:\/\/wellforces.co.nz\/customer_authentication\/redirect?locale=en\u0026region_country=NZ\"\u003e\n \u003cspan \u003ePlease \u003c\/span\u003e \u003cspan class=\"login-text\"\u003eLogin\u003c\/span\u003e \u003cspan\u003e for Pricing\u003c\/span\u003e\n \u003c\/a\u003e", "volume_html" :"\u003cvolume-pricing class=\"parent-display inside_product_form\" id=\"volume-pricing-main\" \u003e\u003c\/volume-pricing\u003e" } ] }

Mean Well HRP-200-15 Power Supply 201W 15V 13.4A

Select model — 7 in this family

Overview

Features

Specifications

OUTPUT

INPUT

PROTECTION

ENVIRONMENT

SAFETY & EMC (Note 4)

OTHERS

Technical drawings

Downloads

Certificates4

Test reports1

Catalogues1

FAQ

Payment & Security

Other HRP-200 Models

Write a review

Your cart

Mean Well HRP-200-15 Power Supply 201W 15V 13.4A

Features

Company Information

Services and Support

Choose options