Over 15 years experience of providing support of MEAN WELL Power Supplies
Mean Well PM-15-24 Power Supply 15W 24V 630mA
Log in to see priceOverview
PM-15-24 is the 24V output model of this series: rated current 0.63A, rated power 15.12W, typical efficiency 81%.
Features
- Universal AC input / Full range
- Protections: Short circuit / Overload / Over voltage
- Ultra-miniature size, light weight
- Cooling by free air convection
- Isolation classⅡ
- Medical safety approved (2 x MOPP between primary to secondary)
- No load power consumption<0.5W
- 100% full load burn-in test
- Fixed switching frequency at 67KHz
- High reliability
- Suitable for BF application with appropriate system consideration
- 3 years warranty
Specifications
OUTPUT
- DC VOLTAGE
- 24V
- RATED CURRENT
- 0.63A
- CURRENT RANGE
- 0 ~ 0.63A
- RATED POWER
- 15.12W
- RIPPLE & NOISE (max.)Note.2
- 240mVp-p
- VOLTAGE TOLERANCENote.3
- ±2.0%
- LINE REGULATION
- ±0.5%
- LOAD REGULATION
- ±0.5%
- SETUP, RISE TIME
- 1000ms, 20ms/230VAC 1000ms, 20ms/115VAC at full load
- HOLD UP TIME (Typ.)
- 100ms/230VAC 24ms/115VAC at full load
INPUT
- VOLTAGE RANGE
- 85 ~ 264VAC 120 ~ 370VDC
- FREQUENCY RANGE
- 47 ~ 440Hz
- EFFICIENCY (Typ.)
- 81%
- AC CURRENT (Typ.)
- 0.35A/115VAC 0.2A/230VAC
- INRUSH CURRENT (Typ.)
- COLD START 30A/115VAC 50A/230VAC
- LEAKAGE CURRENTNote.5
- Touch current < 80μ A/264VAC
PROTECTION
- OVERLOAD
- Above 105% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed
- OVER VOLTAGE
- 27.6 ~ 32.4V Protection type : Shut off o/p voltage, clamping by zener diode
ENVIRONMENT
- WORKING TEMP.
- -20 ~ +70℃ (Refer to "Derating Curve")
- WORKING HUMIDITY
- 20 ~ 90% RH non-condensing
- STORAGE TEMP., HUMIDITY
- -40 ~ +85℃, 10 ~ 95% RH
- TEMP. COEFFICIENT
- ±0.03%/℃ (0 ~ 50℃)
- VIBRATION
- 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY & EMC (Note 4)
- SAFETY STANDARDS
- ANSI/AAMI ES60601-1, TUV EN60601-1, IEC60601-1, UL60950-1, EAC TP TC 004 approved
- ISOLATION LEVEL
- Primary-Secondary: 2xMOPP
- WITHSTAND VOLTAGE
- I/P-O/P:4KVAC
- ISOLATION RESISTANCE
- I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
- EMC EMISSION
- Compliance to EN55011(CISPR11),EN55032 (CISPR32) Class B, EN61000-3-2,-3, EAC TP TC 020
- EMC IMMUNITY
- Compliance to EN61000-4-2,3,4,5,6,8,11, EN55035, EN60601-1-2, EN61204-3, medical level, EAC TP TC 020
OTHERS
- MTBF
- 499.7Khrs min. MIL-HDBK-217F (25℃)
- DIMENSION
- 75*53*22.7mm (L*W*H)
- PACKING
- 0.14Kg; 120pcs/17.8Kg/0.94CUFT
Test conditions and notes6
- 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
- 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
- 3. Tolerance : includes set up tolerance, line regulation and load regulation.
- 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives.
- 5. Touch current was measured from primary input to DC output.
- 6. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
Technical drawings
Downloads
Certificates5
Test reports1
Catalogues1
FAQ
Can I use the PM-15-24 for a small 24V industrial control circuit?
Yes, it is a constant-voltage 24V supply rated for 0.63A and 15.12W. That makes it a fit for small 24V control loads in industrial or automation equipment as long as the total demand stays within 0.63A and 15.12W.
Is the PM-15-24 suitable for powering 24V sensors and relays in an automation panel?
It can be used for 24V sensors, relays, and similar low-power panel devices that need regulated 24V DC. The key limit is the available 0.63A output current and 15.12W total output power.
Can this 24V power supply run embedded or HMI-related electronics that use 24V input?
It is intended for constant-voltage 24V applications, so it can support embedded or interface hardware designed for a 24V DC input. You need to keep the connected load at or below 15.12W and 0.63A.
Is the PM-15-24 meant for indoor or outdoor environments?
The listed operating temperature range is -20°C to +70°C, but no IP rating is provided in the product specs. Based on the available data, the product information supports temperature suitability only and does not indicate sealed outdoor or wet-location protection.
Payment & Security
Payment methods
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Other PM-15 Models
4 other models| Model | Power | Voltage | Current | |
|---|---|---|---|---|
| Mean Well PM-15-5 Power Supply 15W 5V 3A | 15W | 5V | 3A | View |
| Mean Well PM-15-3.3 Power Supply 15W 3.3V 3.5A | 11.55W | 3.3V | 3.5A | View |
| Mean Well PM-15-15 Power Supply 15W 15V 1A | 15W | 15V | 1A | View |
| Mean Well PM-15-12 Power Supply 15W 12V 1.25A | 15W | 12V | 1.25A | View |
Please log in to write a review.
Write a review
Reviews are checked before publishing. By submitting you confirm this is your genuine experience with this product.
Submitting your review…
It's published and now helps other buyers.
We're checking it and it'll appear shortly.
Please try again.
