Image shown is a representation only. Exact specifications should be obtained from the product datasheet.

Mean Well HRP-75-7.5 Power Supply 75W 7.5V 10A

built-in active PFChigh efficiency up to 90%no load power consumption <0.5W~0.75W

SKU HRP-75-7.5

Log in to see price Trade pricing & online ordering for account holders

Select model — 7 in this family

HRP-75-7.5

HRP-75-7.5 75W 7.5V Backorder

HRP-100-7.5 100W 7.5V Backorder

HRP-150-7.5 150W 7.5V Backorder

HRP-200-7.5 200W 7.5V Backorder

HRP-300-7.5 300W 7.5V Low stock

HRP-450-7.5 450W 7.5V Backorder

HRP-600-7.5 600W 7.5V In stock

Product variants

Available to order

Overview

HRP-75-7.5 is the 7.5V output model of this series: rated current 10A, rated power 75W, typical efficiency 84%.

Features

Universal AC input / Full range
Built-in active PFC function
Withstand 300VAC surge input for 5 seconds
Protections: Short circuit / Overload / Over voltage
Protections: Over temperature (optional)
Cooling by free air convection
1U low profile 38mm
Built-in remote ON-OFF control
No load power consumption<0.5W
All using 105℃ long life electrolytic capacitors
5 years warranty

Specifications

HRP-75-7.5Specifications from the official datasheet (2026-04-03 edition)

OUTPUT

DC VOLTAGE: 7.5V
RATED CURRENT: 10A
CURRENT RANGE: 0 ~ 10A
RATED POWER: 75W
RIPPLE & NOISE (max.)^Note.2: 100mVp-p
VOLTAGE ADJ. RANGE: 7.1 ~ 9V
VOLTAGE TOLERANCE^Note.3: ±2.5%
LINE REGULATION: ±1.0%
LOAD REGULATION: ±1.5%
SETUP, RISE TIME: 1800ms, 25ms/230VAC 1800ms, 25ms/115VAC at full load
HOLD UP TIME (Typ.): 50ms/230VAC 20ms/115VAC at full load

INPUT

VOLTAGE RANGE^Note.5: 85 ~ 264VAC 120 ~ 370VDC
FREQUENCY RANGE: 47 ~ 63Hz
POWER FACTOR (Typ.): PF>0.9/230VAC PF>0.95/115VAC at full load
EFFICIENCY (Typ.): 84%
AC CURRENT (Typ.): 0.9A/115VAC 0.5A/230VAC
INRUSH CURRENT (Typ.): 35A/115VAC 65A/230VAC
LEAKAGE CURRENT: <1mA / 240VAC

PROTECTION

OVERLOAD: 105 ~ 135% rated output power Protection type : Constant current limiting, switch to hiccup mode for Vo<50% of rated voltage, recovers automatically after fault condition is removed
OVER VOLTAGE: 9.4 ~ 10.9V Protection type : Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE (OPTIONAL): Shut down o/p voltage, recovers automatically after temperature goes down

FUNCTION

REMOTE CONTROL: RC+ / RC-: 0 ~ 0.8V = power on ; 4 ~ 10V = power off

ENVIRONMENT

WORKING TEMP.: -40 ~ +70℃ (Refer to "Derating Curve")
WORKING HUMIDITY: 20 ~ 90% RH non-condensing
STORAGE TEMP., HUMIDITY: -40 ~ +85℃, 10 ~ 95% RH
TEMP. COEFFICIENT: ±0.03%/℃ (0 ~ 50℃)
VIBRATION: 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes

SAFETY & EMC (Note 4)

SAFETY STANDARDS: UL62368-1,TUV BS EN/EN62368-1, AS/NZS62368.1, EAC TP TC 004 approved
WITHSTAND VOLTAGE: I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
ISOLATION RESISTANCE: I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION: Compliance to BS EN/EN55032 (CISPR32) Class B, BS EN/EN61000-3-2,-3, EAC TP TC 020
EMC IMMUNITY: Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11,BS EN/EN55035 , BS EN/ EN61000-6-2 ,heavy industry level, EAC TP TC 020

OTHERS

MTBF: 2385.6K hrs min. Telcordia SR-332 (Bellcore) ; 352.7K hrs min. MIL-HDBK-217F (25℃)
DIMENSION: 129*98*38mm (L*W*H)
PACKING: 0.47Kg; 30pcs/ 15Kg/ 0.97CUFT

Test conditions and notes7

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1μF & 47μF parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on a 360mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf )
5. Derating may be needed under low input voltages. Please check the derating curve for more details.
6. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
7. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).

Technical drawings

HRP-75-7.5 Mechanical Specification — Mechanical Specification

HRP-75-7.5 Block Diagram — Block Diagram

HRP-75-7.5 Derating Curve — Derating Curve

Downloads

Certificates3

UL Certificate (HRP-75)(EN) PDF Download

TUV Certificate (HRP-75)(EN) PDF Download

EMC Certificate (HRP-75)(EN) PDF Download

Test reports1

Test Report (HRP-75-5)(EN) PDF Download

Catalogues1

Mean Well Catalog (Industrial) PDF Download

FAQ

Can I use the HRP-75-7.5 for 7.5V industrial or embedded electronics?

Yes, if the equipment requires 7.5V constant voltage and the total load stays within 10A and 75W. That suits 7.5V electronics, control boards, or embedded assemblies that need a regulated 7.5V rail at up to 10A.

Is the HRP-75-7.5 a fit for 7.5V instrumentation or bench test systems?

It can be used for instrumentation or test systems that run from a regulated 7.5V rail and need up to 75W. The 85-264VAC input makes it practical in facilities with different AC mains standards.

Can this model support legacy 7.5V automation electronics?

It is appropriate where older or specialized automation electronics call for 7.5V constant voltage and stay below 10A. The -40°C to +70°C operating range (with derating per the derating curve) can also help in equipment that must tolerate broad ambient conditions.

How does the HRP-75-7.5 compare with the other HRP-75 versions?

The HRP-75 family includes 3.3V 49.5W 15A, 5V 75W 15A, 7.5V 75W 10A, 12V 75.6W 6.3A, 15V 75W 5A, 24V 76.8W 3.2A, 36V 75.6W 2.1A, and 48V 76.8W 1.6A. The 7.5V model sits between the 5V and 12V versions and is mainly chosen when the load specifically requires 7.5V.

Can the HRP-75-7.5 be used in hot or cold protected enclosures?

Its rated operating window is -40°C to +70°C, with output derating at the upper end per the derating curve (-40°C start-up is possible with 230VAC input), so the temperature capability is broad. The provided specs do not include an IP rating, so use in exposed outdoor conditions should not be assumed from the temperature range alone.

Payment & Security

Payment methods

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Model	Power	Voltage	Current
Mean Well HRP-75-5 Power Supply 75W 5V 15A	75W	5V	15A	View
Mean Well HRP-75-48 Power Supply 76.8W 48V 1.6A	76.8W	48V	1.6A	View
Mean Well HRP-75-36 Power Supply 75.6W 36V 2.1A	75.6W	36V	2.1A	View
Mean Well HRP-75-3.3 Power Supply 49.5W 3.3V 15A	49.5W	3.3V	15A	View
Mean Well HRP-75-24 Power Supply 76.8W 24V 3.2A	76.8W	24V	3.2A	View
Mean Well HRP-75-15 Power Supply 75W 15V 5A	75W	15V	5A	View
Mean Well HRP-75-12 Power Supply 75.6W 12V 6.3A	75.6W	12V	6.3A	View

Please log in to write a review.

{ "id":8343889150251, "variants" :[{ "context":"default", "variant_id": 45321002516779, "sku":"HRP-75-7.5", "inventory_qty" : 0, "customer" :false, "custom_html" :"\u003ca class=\"text-current logged-out-price logged-out\" href=\"https:\/\/wellforces.co.nz\/customer_authentication\/redirect?locale=en\u0026region_country=NZ\"\u003e\n \u003cspan \u003ePlease \u003c\/span\u003e \u003cspan class=\"login-text\"\u003eLogin\u003c\/span\u003e \u003cspan\u003e for Pricing\u003c\/span\u003e\n \u003c\/a\u003e", "volume_html" :"\u003cvolume-pricing class=\"parent-display inside_product_form\" id=\"volume-pricing-main\" \u003e\u003c\/volume-pricing\u003e" } ] }

Mean Well HRP-75-7.5 Power Supply 75W 7.5V 10A

Select model — 7 in this family

Overview

Features

Specifications

OUTPUT

INPUT

PROTECTION

FUNCTION

ENVIRONMENT

SAFETY & EMC (Note 4)

OTHERS

Technical drawings

Downloads

Certificates3

Test reports1

Catalogues1

FAQ

Payment & Security

Other HRP-75 Models

Write a review

Your cart

Mean Well HRP-75-7.5 Power Supply 75W 7.5V 10A

Features

Company Information

Services and Support

Choose options