Over 15 years experience of providing support of MEAN WELL Power Supplies
Image shown is a representation only. Exact specifications should be obtained from the product datasheet.
Mean Well LDD-350HW DC/DC LED Driver CC 350mA - Step-down
Log in to see priceOverview
LDD-350HW is the model of this series: typical efficiency 97% at full load and 36VDC/48VDC input for LDD-H/HW ; 96% at full load and 36VDC/48VDC input for LDD-HS.
Features
- DC/DC step-down converter
- Constant current output: 300mA to 1500mA
- Wide input voltage: 9 ~ 56VDC
- Wide output LED string voltage: 2 ~ 52VDC
- High efficiency up to 97%
- Built-in EMI filter, comply with BS EN/EN55015 and FCC part15 without additional input filter and capacitors
- Built-in PWM and remote ON/OFF control
- Protections: Short circuit / Over temperature
- Cooling by free air convection
- Fully encapsulated with IP67 level for pin and wire style
- Non-potted, optional conformal coating for SMD style (Order No.: LDD- 350-1000 HSC)
- Compact size
- Low cost, high reliability
- Suitable for driving illumination LED
- 3 years warranty
Specifications
OUTPUT
- CURRENT RANGE
- 350mA
- VOLTAGE RANGENote.4
- 2 ~ 52VDC
- CURRENT ACCURACY (Typ.)
- Β±3% at 24VDC input ; Β±4% at 48VDC input for LDD-H/HW ; Β±5% for LDD-HS
- RIPPLE & NOISE(max.)Note.2
- 150mVp-p
- SWITCHING FREQENCY
- 40KHz ~ 1000KHz
- EXTERNAL CAPACITANCE LOAD (max.)
- 2.2uF
INPUT
- VOLTAGE RANGE
- 9 ~ 56VDC
- EFFICIENCY (max.)
- 97% at full load and 36VDC/48VDC input for LDD-H/HW ; 96% at full load and 36VDC/48VDC input for LDD-HS
- DC CURRENT Full loadNote.3
- 320mA
- DC CURRENT No load
- 5mA
- FILTER
- Capacitor
PWM DIMMING & ON/OFF CONTROL
- REMOTE ON/OFF
- Leave open if not use
- REMOTE ON/OFF
- Power ON with dimming: DIM ~ -Vin >2.5 ~ 6VDC or open circuit
- REMOTE ON/OFF
- Power OFF : DIM ~ -Vin < 0.8VDC or short
- PWM FREQUENCY
- 100 ~ 1KHz
- QUIESCENT INPUT CURRENT IN SHUTDOWN MODE(max.)
- 1mA at PWM dimming OFF and 24VDC input
PROTECTION
- SHORT CIRCUIT
- Regulated at rated output current Protection type: Can be continued, recovers automatically after fault condition is removed
- OVER TEMPERATURE
- Tj 150β typically(IC1) detect on main control IC Protection type : Shut down, recovers automatically after temperature goes down
ENVIRONMENT
- WORKING TEMP.
- -40 ~ + 85β(Refer to derating curve)
- WORKING HUMIDITY
- 20% ~ 90% RH non-condensing for LDD-H/HW ; 20%~85% RH non-condensing for LDD-HS
- STORAGE TEMP., HUMIDITY
- -55 ~ +125β, 10 ~ 95% RH
- TEMP. COEFFICIENT
- Β±0.03% / β
- VIBRATION
- 10 ~ 500Hz, 2G 10min./1 cycle, period for 60min. each along X, Y, Z axes
- OPERATING CASE TEMP. (max.)
- 100β
EMC
- SAFETY STANDARDS
- EAC TP TC 020/2011 approved
- EMC EMISSION
- Compliance to BS EN/EN55015, FCC part 15 class B, EAC TP TC 020
- EMC IMMUNITY
- Compliance to BS EN/EN61000-4-2,3,4,6,8, light industry level, criteria A, EAC TP TC 020
OTHERS
- MTBF
- 1000Khrs min. MIL-HDBK-217F (25β)
- DIMENSION
- 31.8*20.3*12.2mm or 1.25"*0.8"*0.48" inch (L*W*H) for LDD-H/HW ; 31.8*20.3*11.4mm or 1.25"*0.8"*0.45" inch (L*W*H) for LDD-HS
- WEIGHT
- LDD-H:15.6g ; LDD-HW:18g ; LDD-HS:12.8g
- POTTING MATERIAL
- Expoxy(UL94-V0) for LDD-H/HW ; without potted for LDD-HS
Test conditions and notes5
- 1.All parameters are specified at normal input(48VDC), rated load, 25β 70% RH ambient.
- 2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf capacitor.
- 3.Test condition: 48VDC input.
- 4.Output voltage will always step down by 3 volts from input DC voltage.
- 5.The output of LDD-H should not be connected to the input of the same unit or output from other sources.
Technical drawings
Downloads
FAQ
Can I use the LDD-350HW for a 350mA LED downlight with a higher forward voltage string?
Yes, this model is useful for 350mA constant current downlight loads that need a wide voltage window. Its LED string voltage range is 2-52VDC, and the output always steps down about 3V from the 9-56VDC input, so supply a voltage above the string voltage.
Is the LDD-350HW a good fit for LED signage modules?
It can be used for signage modules that are specified for 350mA constant current operation. The load needs to remain within the 2-52V constant current range, and this driver should not be used as a constant voltage source.
Can this model power a small LED array in a compact housing?
Yes, it is designed for compact constant current LED systems and measures 31.8 Γ 20.3 Γ 12.2 mm. The LED array must be a 350mA load with a total forward voltage inside 2-52V.
How do I size LED strings for the LDD-350HW?
This driver delivers 350mA constant current over a 2-52V range. The number of LEDs depends on each LED's forward voltage, so you size the string by total forward voltage rather than assuming a specific LED count.
Can the LDD-350HW handle outdoor or industrial temperature swings?
It is fully encapsulated to IP67 and has an operating temperature range of -40Β°C to +85Β°C (refer to the derating curve). That makes it suitable for sealed LED assemblies that may see water exposure, dust, and wide temperature variation.
How does the LDD-350HW differ from other 350mA LDD options?
In the LDD-H series, the LDD-350H, LDD-350HS, and LDD-350HW all deliver 350mA over a 2-52V range. The H is pin style and the HW wire style, both epoxy-encapsulated to IP67 with up to 97% efficiency; the HS is a non-potted SMD style with up to 96% efficiency. The LDD-350HW is the wire-style version with UL3385 22AWG leads.
Payment & Security
Payment methods
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Other LDD Series Models
46 other modelsPlease log in to write a review.
Write a review
Reviews are checked before publishing. By submitting you confirm this is your genuine experience with this product.
Submitting your reviewβ¦
It's published and now helps other buyers.
We're checking it and it'll appear shortly.
Please try again.
