Over 15 years experience of providing support of MEAN WELL Power Supplies
Image shown is a representation only. Exact specifications should be obtained from the product datasheet.
Mean Well LDD-350LW DC/DC LED Driver CC 350mA - Step-down
Log in to see priceOverview
LDD-350LW is the model of this series: typical efficiency 95% at full load and 24VDC/36VDC input for LDD-300~700L/LW ; 95% at full load and 24VDC input for LDD-300~700LS.
Features
- DC/DC step-down converter
- Constant current output: 300mA to 700mA
- Wide input voltage: 9 ~ 36VDC
- Wide output LED string voltage: 2 ~ 32VDC
- High efficiency up to 95%
- Built-in EMI filter, comply with BS EN/EN55015 and FCC part15 without additional input filter and capacitors
- Built-in PWM dimming and remote ON/OFF control
- Protections: Short circuit / Over temperature
- Cooling by free air convection
- Fully encapsulated with IP67 level for pin and wire style
- Compact size
- Low cost, high reliability
- Suitable for driving illumination LED
- 3 years warranty
Specifications
OUTPUT
- CURRENT RANGE
- 350mA
- VOLTAGE RANGENote.4
- 2 ~ 32VDC for LDD-300~700L/LW ; 2~ 28VDC for LDD-300~700LS
- CURRENT ACCURACY (Typ.)
- Β±5% at 24VDC input
- RIPPLE & NOISE(max.)Note.2
- 150mVp-p
- SWITCHING FREQENCY
- 40KHz ~ 1000KHz
- EXTERNAL CAPACITANCE LOAD (max.)
- 2.2uF
INPUT
- VOLTAGE RANGE
- 9 ~ 36VDC for LDD-300~700L/LW ; 9~ 32VDC for LDD-300~700LS
- EFFICIENCY (max.)
- 95% at full load and 24VDC/36VDC input for LDD-300~700L/LW ; 95% at full load and 24VDC input for LDD-300~700LS
- DC CURRENT Full loadNote.3
- 350mA
- DC CURRENT No load
- 5mA
- FILTER
- Capacitor
PWM DIMMING & ON/OFF CONTROL
- REMOTE ON/OFF
- Leave open if not use Power ON with dimming: DIM ~ -Vin >3.5 ~ 8VDC or open circuit Power OFF : DIM ~ -Vin < 0.5VDC or short
- PWM FREQUENCY
- 100 ~ 1KHz
- QUIESCENT INPUT CURRENT IN SHUTDOWN MODE(max.)
- 1mA at PWM dimming OFF and 24VDC input
PROTECTION
- SHORT CIRCUIT
- Regulated at rated output current Protection type: Can be continued, recovers automatically after fault condition is removed
- OVER TEMPERATURE
- Tj 150β typically(IC1) detect on main control IC Protection type : Shut down, recovers automatically after temperature goes down
ENVIRONMENT
- WORKING TEMP.
- -40 ~ + 85β(Refer to derating curve)
- WORKING HUMIDITY
- 20% ~ 90% RH non-condensing for LDD-300~700L/LW ; 20% ~ 85% RH non-condensing for LDD-300~700LS
- STORAGE TEMP., HUMIDITY
- -55 ~ +125β, 10 ~ 95% RH
- TEMP. COEFFICIENT
- Β±0.03% / β
- VIBRATION
- 10 ~ 500Hz, 2G 10min./1 cycle, period for 60min. each along X, Y, Z axes
- OPERATING CASE TEMP. (max.)
- 100β
EMC
- SAFETY STANDARDS
- EAC TP TC 020/2011 approved
- EMC EMISSION
- Compliance to BS EN/EN55015, FCC part 15 class B, EAC TP TC 020
- EMC IMMUNITY
- Compliance to BS EN/EN61000-4-2,3,4,6,8, light industry level, criteria A, EAC TP TC 020
OTHERS
- MTBF
- 1000Khrs min. MIL-HDBK-217F (25β)
- DIMENSION
- 22.6*9.9*8.9mm or 0.89"*0.39"*0.35" inch (L*W*H) for LDD-300~700L/LW ; 25.4*10.5*9.3mm or 1"*0.4135"*0.366" inch (L*W*H) for LDD-300~700LS
- WEIGHT
- LDD-300~700L:4g ; LDD-300~700LW:7.3g ; LDD-300~700LS :3.4g
- POTTING MATERIAL
- Expoxy(UL94-V0) for LDD-300~700L/LW ; without potted for LDD-300~700LS
Test conditions and notes5
- 1.All parameters are specified at normal input(24VDC), rated load, 25β 70% RH ambient.
- 2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf capacitor.
- 3.Test condition: 24VDC input.
- 4.Output voltage will always step down by 3 volts from input DC voltage.
- 5.The output of LDD-L should not be connected to the input of the same unit or output from other sources.
Technical drawings
Downloads
Certificates5
Catalogues1
FAQ
Can the LDD-350LW be used for a low-voltage LED downlight module?
Yes, it is suited to constant current LED downlight loads at 350mA when the LED string stays within the 2-32V output range. Because it is a step-down driver, the output voltage stays about 3V below the 9-36VDC input voltage.
Is this driver suitable for compact LED signage modules?
It can be used with constant current signage modules that require 350mA. Because its constant current output range is 2-32V, it is intended for lower-voltage LED strings rather than long series arrays.
Can I use the LDD-350LW for a small custom LED array in a tight space?
Yes, this model is physically compact at 22.6 Γ 9.9 Γ 8.9 mm, which helps in small housings. The LED array still needs to be a 350mA constant current load with a combined forward voltage within 2-32V.
How do I check LED compatibility for the LDD-350LW?
The key match points are 350mA constant current and a 2-32V output range. The number of LEDs depends on each LED forward voltage, so this should be evaluated by total forward voltage instead of a fixed LED quantity.
Is the LDD-350LW acceptable for damp or outdoor installations?
This wire-style driver is fully encapsulated to IP67 level and operates from -40Β°C to +85Β°C. That makes it appropriate for sealed LED systems in wet or dusty conditions, provided the LED load stays within its 350mA, 2-32V output.
Payment & Security
Payment methods
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Other LDD Series Models
46 other modelsPlease log in to write a review.
Write a review
Reviews are checked before publishing. By submitting you confirm this is your genuine experience with this product.
Submitting your reviewβ¦
It's published and now helps other buyers.
We're checking it and it'll appear shortly.
Please try again.
