Over 15 years experience of providing support of MEAN WELL Power Supplies
Mean Well PM-05-12 Power Supply 5W 12V 420mA
Log in to see priceOverview
PM-05-12 is the 12V output model of this series: rated current 0.42A, rated power 5.04W, typical efficiency 73%.
Features
- Universal AC input / Full range
- Protections: Short circuit / Overload / Over voltage
- Ultra-miniature size, light weight
- Cooling by free air convection
- Isolation classⅡ
- Medical safety approved (2 x MOPP between primary to secondary)
- No load power consumption<0.5W
- 100% full load burn-in test
- Fixed switching frequency at 67KHz
- High reliability
- Suitable for BF application with appropriate system consideration
- 3 years warranty
Specifications
OUTPUT
- DC VOLTAGE
- 12V
- RATED CURRENT
- 0.42A
- CURRENT RANGE
- 0 ~ 0.42A
- RATED POWER
- 5.04W
- RIPPLE & NOISE (max.)Note.2
- 150mVp-p
- VOLTAGE TOLERANCENote.3
- ±2.0%
- LINE REGULATION
- ±0.5%
- LOAD REGULATION
- ±1.0%
- SETUP, RISE TIME
- 1000ms, 20ms/230VAC 1000ms, 20ms/115VAC at full load
- HOLD UP TIME (Typ.)
- 100ms/230VAC 24ms/115VAC at full load
INPUT
- VOLTAGE RANGE
- 85 ~ 264VAC 120 ~ 370VDC
- FREQUENCY RANGE
- 47 ~ 440Hz
- EFFICIENCY (Typ.)
- 73%
- AC CURRENT (Typ.)
- 0.12A/115VAC 0.08A/230VAC
- INRUSH CURRENT (Typ.)
- COLD START 25A/115VAC 45A/230VAC
- LEAKAGE CURRENTNote.5
- Touch current < 80μ A/264VAC
PROTECTION
- OVERLOAD
- Above 105% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed
- OVER VOLTAGE
- 13.8 ~ 16.2V Protection type : Shut off o/p voltage, clamping by zener diode
ENVIRONMENT
- WORKING TEMP.
- -20 ~ +70℃ (Refer to "Derating Curve")
- WORKING HUMIDITY
- 20 ~ 90% RH non-condensing
- STORAGE TEMP., HUMIDITY
- -40 ~ +85℃, 10 ~ 95% RH
- TEMP. COEFFICIENT
- ±0.03%/℃ (0 ~ 50℃)
- VIBRATION
- 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY & EMC
- SAFETY STANDARDS
- ANSI/AAMI ES60601-1, TUV EN60601-1, IEC60601-1, EAC TP TC 004 approved
- ISOLATION LEVEL
- Primary-Secondary: 2xMOPP
- WITHSTAND VOLTAGE
- I/P-O/P:4KVAC
- ISOLATION RESISTANCE
- I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
- EMC EMISSION
- Compliance to EN55011(CISPR11),EN55032 (CISPR32) Class B, EN61000-3-2,-3, EAC TP TC 020
- EMC IMMUNITY
- Compliance to EN61000-4-2,3,4,5,6,8,11, EN55035, EN60601-1-2, EN61204-3, medical level, EAC TP TC 020
OTHERS
- MTBF
- 1513.4Khrs min. MIL-HDBK-217F (25℃)
- DIMENSION
- 62.85*50*19.7mm (L*W*H)
- PACKING
- 0.079Kg; 120pcs/10.5Kg/0.94CUFT
Test conditions and notes6
- 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
- 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
- 3. Tolerance : includes set up tolerance, line regulation and load regulation.
- 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives.
- 5. Touch current was measured from primary input to DC output.
- 6. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
Technical drawings
Downloads
FAQ
Can I use the PM-05-12 for a small 12V PLC I/O module or relay board?
Yes, if the load needs a constant 12V DC supply and stays within 0.42A and 5.04W. That makes it a fit for low-power industrial control electronics rather than higher-draw 12V devices.
Is the PM-05-12 suitable for powering a 12V sensor, transmitter, or signal interface in an automation panel?
It can be used for low-power 12V automation electronics that require constant voltage output. The key limit is the available 12V at 0.42A, with total output capped at 5.04W.
Can this 12V power supply run a compact embedded controller or communications board?
It is appropriate for embedded or control boards that are designed for 12V DC input and have modest power demand. The board and any attached accessories must remain under 0.42A and 5.04W.
Would the PM-05-12 work for 12V alarm, annunciator, or status-indication hardware?
Yes, it can suit small 12V indication and control-cabinet devices when the load is within the unit's constant-voltage 12V output range. Its 5.04W rating means it is best for lighter-duty electronics, not larger 12V loads.
How does the PM-05-12 compare with the other PM family options listed here?
In the PM-05 5W series, the related options are PM-05-15 at 4.95W, 15V, 0.33A; PM-05-24 at 5.52W, 24V, 0.23A; PM-05-3.3 at 4.125W, 3.3V, 1.25A; and PM-05-5 at 5W, 5V, 1A. All share the same 85-264VAC input, so the main difference is the output voltage and the current available at that voltage.
Is the PM-05-12 suitable for outdoor or unprotected locations?
The provided specs show an operating temperature range of -20°C to +70°C, but no IP rating is listed. Based on that, it is better treated as a power supply for protected indoor equipment or enclosed systems rather than exposed outdoor use.
Payment & Security
Payment methods
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Other PM-05 Models
4 other models| Model | Power | Voltage | Current | |
|---|---|---|---|---|
| Mean Well PM-05-5 Power Supply 5W 5V 1A | 5W | 5V | 1A | View |
| Mean Well PM-05-3.3 Power Supply 5W 3.3V 1.25A | 4.125W | 3.3V | 1.25A | View |
| Mean Well PM-05-24 Power Supply 5W 24V 230mA | 5.52W | 24V | 0.23A | View |
| Mean Well PM-05-15 Power Supply 5W 15V 330mA | 4.95W | 15V | 0.33A | View |
Please log in to write a review.
Write a review
Reviews are checked before publishing. By submitting you confirm this is your genuine experience with this product.
Submitting your review…
It's published and now helps other buyers.
We're checking it and it'll appear shortly.
Please try again.
