Image shown is a representation only. Exact specifications should be obtained from the product datasheet.

Mean Well SE-1500-15 Power Supply 1500W 15V 100A

economical model medium to high power(450W~1500W)

SKU SE-1500-15

Log in to see price Trade pricing & online ordering for account holders

Available to order

Overview

SE-1500-15 is the 15V output model of this series: rated current 100A, rated power 1500W, typical efficiency 85%.

Features

AC input 180 ~ 264VAC
AC input active surge current limiting
Protections: Short circuit / Overload / Over voltage / Over temperature
Forced air cooling by built-in DC ball bearing fan
High power density 7.8w/inch³
With DC OK signal output
Built-in remote ON-OFF control
Built-in remote sense function
UL / CUL approved
Low cost
2 years warranty

Specifications

SE-1500-15Specifications from the official datasheet (2026-09-07 edition)

OUTPUT

DC VOLTAGE: 15V
RATED CURRENT: 100A
CURRENT RANGE: 0 ~ 100A
RATED POWER: 1500W
RIPPLE & NOISE (max.)^Note.2: 150mVp-p
VOLTAGE ADJ. RANGE: 13.5 ~ 16.5V
VOLTAGE TOLERANCE^Note.3: ±1.0%
LINE REGULATION: ±0.5%
LOAD REGULATION: ±0.5%
SETUP, RISE TIME: 150ms, 12ms / 230VAC at full load
HOLD UP TIME (Typ.): 26ms / 230VAC at full load

INPUT

VOLTAGE RANGE: 180 ~ 264VAC 254 ~ 370VDC
FREQUENCY RANGE: 47 ~ 63Hz
EFFICIENCY (Typ.): 85%
AC CURRENT (Typ.): 17.5A / 230VAC
INRUSH CURRENT (Typ.): 60A / 230VAC
LEAKAGE CURRENT: <3.5mA / 240VAC

PROTECTION

OVERLOAD: 105 ~ 125% rated output power Protection type : Shut down o/p voltage, re-power on to recover
OVER VOLTAGE: 18 ~ 21V Protection type : Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE: Shut down o/p voltage, recovers automatically after temperature goes down

FUNCTION

DC_OK SIGNAL: PSU turn on:3.3V ~ 5.6V PUS turn off:0 ~ 1V
REMOTE CONTROL: RC+/RC-: 0 ~ 0.8V power on; 4 ~ 10V power off

ENVIRONMENT

WORKING TEMP.: -20 ~ +70℃ (Refer to "Derating Curve")
WORKING HUMIDITY: 20 ~ 90% RH non-condensing
STORAGE TEMP., HUMIDITY: -40 ~ +85℃, 10 ~ 95% RH
TEMP. COEFFICIENT: ±0.05%/℃ (0 ~ 50℃)
VIBRATION: 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes

SAFETY & EMC

SAFETY STANDARDS: UL62368-1 , BSMI CNS15598-1, EAC TP TC 004 approved; Design refer to BS EN/EN62368-1
WITHSTAND VOLTAGE: I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
ISOLATION RESISTANCE: I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION: Parameter Standard Test Level

Conducted BS EN/ EN55032 (CISPR32),CNS15936 Class A
Radiated BS EN/ EN55032 (CISPR32),CNS15936 Class A
Harmonic Current BS EN/ EN61000-3-2
Voltage Flicker BS EN/ EN61000-3-3
EMC IMMUNITY^{Note 4}: BS EN/ EN55035, BS EN/ EN61000-6-2

Parameter Standard Test Level

ESD BS EN/ EN61000-4-2 Level 3, 8KV air; Level 2, 4KV contact
Radiated BS EN/ EN61000-4-3 Level 3
EFT / Burst BS EN/ EN61000-4-4 Level 3
Surge BS EN/ EN61000-6-2 1KV/Line-Line 2KV/Line-Earth
Conducted BS EN/ EN61000-4-6 Level 3
Magnetic Field BS EN/ EN61000-4-8 Level 4
Voltage Dips and Interruptions BS EN/ EN61000-4-11 >95% dip 0.5 periods, 30% dip 25 periods, >95% interruptions 250 periods

Parameter	Standard	Test Level
Conducted	BS EN/ EN55032 (CISPR32),CNS15936	Class A
Radiated	BS EN/ EN55032 (CISPR32),CNS15936	Class A
Harmonic Current	BS EN/ EN61000-3-2
Voltage Flicker	BS EN/ EN61000-3-3

Parameter	Standard	Test Level
ESD	BS EN/ EN61000-4-2	Level 3, 8KV air; Level 2, 4KV contact
Radiated	BS EN/ EN61000-4-3	Level 3
EFT / Burst	BS EN/ EN61000-4-4	Level 3
Surge	BS EN/ EN61000-6-2	1KV/Line-Line 2KV/Line-Earth
Conducted	BS EN/ EN61000-4-6	Level 3
Magnetic Field	BS EN/ EN61000-4-8	Level 4
Voltage Dips and Interruptions	BS EN/ EN61000-4-11	>95% dip 0.5 periods, 30% dip 25 periods, >95% interruptions 250 periods

OTHERS

MTBF: 999.9K hrs min. Telcordia SR-332 (Bellcore) ; 134.5K hrs min. MIL-HDBK-217F (25℃)
DIMENSION: 278*177.8*63.5mm (L*W*H)
PACKING: 3.3Kg; 4pcs/14.2Kg/1.14CUFT

Test conditions and notes6

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on a 720mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)
5. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
6. This power supply does not meet the harmonic current requirements outlined by EN61000-3-2. Please do not use this power supply under the following conditions: a) the end-devices is used within the European Union, and b) the end-devices is connected to public mains supply with 220Vac or greater rated nominal voltage, and c) the power supply is: - installed in end-devices with average or continuous input power greater than 75W, or - belong to part of a lighting system Exception: Power supplies used within the following end-devices do not need to fulfill EN61000-3-2 a) professional equipment with a total rated input power greater than 1000W; b) symmetrically controlled heating elements with a rated power less than or equal to 200W

Technical drawings

SE-1500-15 Mechanical Specification — Mechanical Specification

SE-1500-15 Block Diagram — Block Diagram

SE-1500-15 Derating Curve — Derating Curve

SE-1500-15 Function Manual — Function Manual

Downloads

Datasheet1

SE-1500-15 datasheetSE-1500-SPEC.PDF · 2026-09-07 edition PDF Download

Certificates1

UL Certificate (SE-1500)(EN) PDF Download

Test reports1

Test Report (SE-1500-15)(EN) PDF Download

Catalogues1

Mean Well Catalog (Industrial) PDF Download

FAQ

Can I use the SE-1500-15 for a high-current 15V industrial control system?

Yes, this model is a constant-voltage 15V supply rated for up to 100A and 1500W. It fits 15V industrial or automation equipment that needs a regulated 15V DC bus within that power and current limit.

Is the SE-1500-15 suitable for a 15V embedded test rack or burn-in fixture?

It can be a fit for a centralized 15V source in embedded validation or burn-in systems when the rack requires constant-voltage 15V output. The available output is up to 100A with a total power rating of 1500W.

Can this power supply support multiple 15V loads in one automation cabinet?

It is intended for constant-voltage 15V distribution, so it can serve multiple 15V loads if their combined demand stays within 100A and 1500W. Buyers typically use a supply in this class when they need one higher-power 15V source rather than several smaller units.

Is the SE-1500-15 okay for outdoor or washdown environments?

The listed specs do not provide an IP rating, so outdoor or washdown suitability is not established by this product data. The published operating temperature range is -20°C to +70°C, but temperature range alone does not indicate water or dust protection.

How does the SE-1500-15 compare with other SE-1500 models?

Within the SE-1500 family, the listed versions are 5V 300A 1500W, 12V 125A 1500W, 15V 100A 1500W, 24V 62.5A 1500W, 27V 55.6A 1501.2W, and 48V 31.3A 1502.4W. The main difference is the output voltage and corresponding current rating for each model.

Payment & Security

Payment methods

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Model	Power	Voltage	Current
Mean Well SE-1500-5 Power Supply 1500W 5V 300A	1500W	5V	300A	View
Mean Well SE-1500-48 Power Supply 1500W 48V 31.3A	1502.4W	48V	31.3A	View
Mean Well SE-1500-27 Switching Power Supplies 1501.2W 27V 55.6A Enclosed	1501.2W	27V	55.6A	View
Mean Well SE-1500-24 Power Supply 1500W 24V 62.5A	1500W	24V	62.5A	View
Mean Well SE-1500-12 Power Supply 1500W 12V 125A	1500W	12V	125A	View

Please log in to write a review.

{ "id":8343957438763, "variants" :[{ "context":"default", "variant_id": 45321628352811, "sku":"SE-1500-15", "inventory_qty" : 0, "customer" :false, "custom_html" :"\u003ca class=\"text-current logged-out-price logged-out\" href=\"https:\/\/wellforces.co.nz\/customer_authentication\/redirect?locale=en\u0026region_country=NZ\"\u003e\n \u003cspan \u003ePlease \u003c\/span\u003e \u003cspan class=\"login-text\"\u003eLogin\u003c\/span\u003e \u003cspan\u003e for Pricing\u003c\/span\u003e\n \u003c\/a\u003e", "volume_html" :"\u003cvolume-pricing class=\"parent-display inside_product_form\" id=\"volume-pricing-main\" \u003e\u003c\/volume-pricing\u003e" } ] }

Mean Well SE-1500-15 Power Supply 1500W 15V 100A

Overview

Features

Specifications

OUTPUT

INPUT

PROTECTION

FUNCTION

ENVIRONMENT

SAFETY & EMC

OTHERS

Technical drawings

Downloads

Datasheet1

Certificates1

Test reports1

Catalogues1

FAQ

Payment & Security

Other SE-1500 Models

Write a review

Your cart

Mean Well SE-1500-15 Power Supply 1500W 15V 100A

Features

Company Information

Services and Support

Choose options